Konfigurasi EIGRP Pada Cisco Packet Tracer

Konfigurasi EIGRP Pada Cisco Packet Tracer

Awal mula sebelum melakukan Konfigurasi EIGRP,
kita buat jarinagan sederhana seperti di bawah...

 Pertama, berikan IP Address pada semua PC yang terhubung. Contoh sebagai berikut :
 - Pemberian IP address pada PC0 ...

 - Pemberian IP address pada PC1 ...

- Dan pemberian IP address pada PC2 ...
  

Kedua, atau tahap selanjutnya berikan IP Address pada setiap router .
Contoh sebagai berikut : 

Router 1

     --- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!



Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.179.9.1 255.255.255.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip add 172.18.10.1 255.255.0.0
Router(config-if)#band 125
Router(config-if)#cl ra 125000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit

Konfigurasi EIGRP pada Router 1,


Router(config)#router eigrp 1
Router(config-router)#net 192.179.9.1 
Router(config-router)#net 172.18.10.1
Router(config-router)#end
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#


Router 2 

  --- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!



Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.180.8.1 255.255.255.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip add 172.18.10.2 255.255.255.0
Router(config-if)#band 125
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit 

Router(config-if)#exit
Router(config)#int se3/0
Router(config-if)#ip add 15.10.10.1 255.0.0.0
Router(config-if)#band 125
Router(config-if)#cl ra 125000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial3/0, changed state to down
Router(config-if)#exit  

Konfigurasi EIGRP pada Router 2,


Router(config)#router eigrp 1
Router(config-router)#net 192.180.8.1 
Router(config-router)#net 172.18.10.2 
Router(config-router)#net 15.10.10.1 
Router(config-router)#end
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#


Router 3

     --- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!



Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.182.2.1 255.255.255.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip add 15.10.10.2 255.0.0.0
Router(config-if)#band 125
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit



Konfigurasi EIGRP pada Router 3,


Router(config)#router eigrp 1
Router(config-router)#net 192.182.2.1 
Router(config-router)#net 15.10.10.2 
Router(config-router)#end
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#

Setelah selesai, sekarang kita test dengan cara PING antar PC client...
demikian dari tutorial ini yang saya buat, apabila masih ada yang kurang jelas bisa ditanyakan...


SELESAI...............

JARINGAN OSPF

Langsung aja ke pokok perbahasan yaitu conxfigurasi jaringan OSPF dengan packet tracer

1)Masukan IP dan Subnet mask pada pada tiap klien seperti gambar yang sudah ada di bagian atas Block
2)Desain jaringan seperti di bawah ini:

3) Configurasi Tiap Router

pengaturan router0
======================
Router>ena
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 10.10.10.1 255.255.255.0
Router(config-if)#no shu
Router(config-if)#ex

Router(config)#int ser2/0
Router(config-if)#ip add 192.168.10.2 255.255.255.252
Router(config-if)#no shu
Router(config-if)#ex

Router(config)#int ser3/0
Router(config-if)#ip add 192.168.10.10 255.255.255.252
Router(config-if)#clock rate 9600
Router(config-if)#no shu
Router(config-if)#ex

Router(config)#router ospf 1
Router(config-router)#network 10.10.10.0 0.0.0.255 area 0
Router(config-router)#network 192.168.10.0 0.0.0.3 area 0
Router(config-router)#network 192.168.10.8 0.0.0.3 area 0
Router(config-router)#ex

Router(config)#int ser2/0
Router(config-if)#band
Router(config-if)#bandwidth 1
Router(config-if)#no shu
Router(config-if)#ex

Router(config)#int ser3/0
Router(config-if)#band
Router(config-if)#bandwidth 9
Router(config-if)#no shu
Router(config-if)#ex
Router(config)#

pengaturan router1
==================

Router>ena
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 172.16.1.17 255.255.255.240
Router(config-if)#no shut
Router(config-if)#ex

Router(config)#int se2/0
Router(config-if)#ip add 192.168.10.1 255.255.255.252
Router(config-if)#no shut
Router(config-if)#ex

Router(config)#int ser3/0
Router(config-if)#ip add 192.168.10.5 255.255.255.252
Router(config-if)#clock rate 9600
Router(config-if)#no shut
Router(config-if)#ex

Router(config)#router ospf 1
Router(config-router)#network 192.168.10.0 0.0.0.3 area 0
Router(config-router)#network 172.16.1.16 0.0.0.15 area 0
Router(config-router)#network 192.168.10.4 0.0.0.3 area 0
Router(config-router)#ex

Router(config)#int ser 2/0
Router(config-if)#bandwidth 1
Router(config-if)#no shu
Router(config-if)#no shutdown
Router(config-if)#ex
Router(config)#int ser3/0
Router(config-if)#band
Router(config-if)#bandwidth 5
Router(config-if)#no shu
Router(config-if)#ex
Router(config)#

Pengaturan Router2
==================
Router>en
Router#conf t
Router(config)#int fa0/0
Router(config-if)#ip add 172.16.1.33 255.255.255.248
Router(config-if)#no shutdown
Router(config-if)#exit

Router(config)#int se3/0
Router(config-if)#ip add 192.168.10.6 255.255.255.252
Router(config-if)#no shutdown
Router(config-if)#exit

Router(config)#int se2/0
Router(config-if)#ip add 192.168.10.9 255.255.255.252
Router(config-if)#no shutdown
Router(config-if)#exit

Router(config)#router ospf 1
Router(config-router)#network 172.16.1.32 0.0.0.7 area 0
Router(config-router)#network 192.168.10.4 0.0.0.3 area 0
Router(config-router)#network 192.168.10.8 0.0.0.3 area 0
Router(config-router)#exit

Router(config)#int se3/0
Router(config-if)#bandwidth 6
Router(config-if)#no sh
Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#bandwidth 10
Router(config-if)#no shu
Router(config-if)#ex